Asheville well pump repair from Candler
Well pump repair in Asheville: we find out why the water stopped first
We repair well pumps, pressure tanks, pressure switches, control boxes and wiring on private wells in and around Asheville, from West Asheville and Enka to Woodfin, Fairview, Swannanoa and Arden, and across our 13-county Western North Carolina service area. Our shop is in Candler, just west of Asheville, so most Asheville calls are a short drive.
A lot of no-water calls turn out not to be the pump at all. We test the parts above ground first and only pull a pump when the readings say it’s done.
No water in Asheville? Check these first
A few minutes with this list can make the call faster, and sometimes it gets the water back on.
- City water or a well? Most homes inside Asheville city limits are on city water. If you pay a city water bill, the problem is on the city side, not a well pump. If your house has a pressure tank and a well cap in the yard, keep going.
- The well breaker. Is it tripped? Reset it once. If it trips again, leave it off and call.
- The tank gauge. A gauge sitting at zero tells us something different than a needle that bounces up and down or one that holds steady.
- One faucet or all of them? If one fixture is weak and the rest are fine, look at that fixture or a filter before you blame the pump.
- Storm or freeze? Lightning often takes out the pressure switch or control box first. After a hard freeze, check the pump house, exposed lines and the switch.
- What the water did before it quit. Sputtering, air or sand right before it stopped is worth telling us. It can point to a low water level or a pump pulling sediment.
What to ask before you hire anyone for pump work
- Will you test the switch, tank, control box and wiring before you pull the pump?
- Will I get a price for the repair before work starts?
- Will a new pump be sized to my well’s depth, water level and how much water the house uses?
- What warranty comes with the work? Ours is spelled out in our service terms.
- Is the work done onsite by a licensed contractor?
Signs your well pump or its controls are failing
- No water at any faucet. Could be the pump, but just as often it’s power, the pressure switch, the control box, a split water line or a well that’s been pumped low.
- Low or surging pressure. Usually the tank, the switch, a clogged filter or a restriction in the plumbing. A weak pump is on the list, just not at the top.
- Short cycling. The pump clicks on and off every few seconds. A pressure tank that’s lost its air charge or a worn switch is the common cause, and it wears a pump out fast.
- Pump runs and won’t shut off. A leak, a worn pump that can’t build pressure, a stuck switch or a well that can’t keep up. See why a well pump won’t shut off.
- Breaker trips. Leave it off and call. Repeated resets can damage wiring or the motor.
- Air, sand or cloudy water after the pump runs. Can point to a low water level, a failing check valve or a pump set too close to the bottom.
- Higher power bill with no other change. A pump that runs longer than it used to is often a leak or a pump losing ground.
More detail on early warning signs is in signs a well pump is failing. If the house is completely out of water right now, see emergency well repair in Asheville and call us.
How a repair visit goes
- A few questions on the phone. What the house is doing, when it started and what the breaker and pressure gauge show. Sometimes that points straight at the problem.
- Testing at the surface. We check voltage at the breaker and control box, the capacitor and relay on three-wire pumps, the pressure switch and the tank’s air charge. We read amp draw to see what the motor’s doing down in the well.
- A straight answer and a price. We tell you what failed, what it’ll take to fix and what it costs, before any work starts. If a repair isn’t worth it, we say so.
- The repair. Switch, control box, tank, wiring, check valve or line repair. If the pump has to come out, we pull it, look over the wire and drop pipe, and match any new pump to the well’s depth, water level and how much water the house uses.
- Checking our work. We restart the system, watch it build and hold pressure, make sure the pump cuts off where it should and run the water until it clears. Our workmanship warranty is in our service terms.

For tank or switch work on its own, see pressure tank replacement and pressure switch repair. When the pump is worn out, see well pump replacement. Not sure where the trouble is? Well diagnostics covers the full troubleshooting visit.
Recent job: no water in Candler
In November 2026 we took a no-water call in Candler, just west of Asheville. The pressure switch had power, but the pump wasn’t running. We pulled the pump and installed a new 1 HP, 10 GPM Grundfos SQ submersible pump with a new check valve and torque arrestor, plus 140 feet of new 10/2 pump wire.
The photos below are from other Case Water Systems pump and wellhead jobs. There are more field photos in our project gallery.


Why pumps fail around Asheville and the mountains
Wells around Asheville, like most in Western North Carolina, are drilled into fractured granite, gneiss and schist. Water comes in through cracks in the rock, so yield can change a lot from one ridge to the next. A pump that’s too big for a slow well will pull it down and run dry. A pump set too low will suck up sediment. Getting the size and setting right matters more here than in flat country.
- Summer storms. Lightning and power blips are one of the most common reasons we get called out. Control boxes, pressure switches and pump motors all take hits.
- Long runs uphill. Plenty of houses around Leicester, Fairview, Weaverville and Madison County sit well above the wellhead, which means more work for the pump and more strain on check valves and tanks. Some need a booster pump or a constant-pressure system.
- Cold snaps. Pump houses, exposed pipes and pressure switches freeze on the north side of the hill. A cracked fitting can look a lot like a dead pump.
- Flood and storm damage. Helene’s flooding along the Swannanoa and French Broad, and washouts all over the region, damaged wellheads, wiring and buried lines. A well that was underwater should be checked, disinfected and tested before you drink from it.
- Second homes and rentals. Systems that sit idle for months come back with lost tank charge and sticky switches, then get hit with a full house of guests.
Submersible and jet pump repair
Most mountain wells use a submersible pump that hangs down inside the well, with the pressure tank and switch in the basement, crawlspace or a pump house. Shallow wells, some older systems and some spring or cistern setups use a jet pump that sits above ground. We repair and replace both.
A jet pump has to keep its suction line full. When it keeps losing prime, it’s usually an air leak on the suction side, a worn foot valve or check valve, or a water level that’s dropped too far. Priming it over and over can burn it up. If a jet pump keeps failing on a well deep enough for a submersible, we’ll lay out both options before any work starts.

On the line between the well and the house, we also fix leaks and breaks. See water line repair.
Asheville neighborhoods and the rest of Western NC
Inside Asheville most homes are on city water, so our Asheville pump calls come from the edges of the city and just past them: West Asheville toward Enka and Candler, Leicester and Sandy Mush, Woodfin and Weaverville out toward Reems Creek and Barnardsville, Fairview, Swannanoa and Black Mountain to the east, and Arden to the south. Some Asheville homes have city water at the street and an older well out back for a garden, pond or barn. We work on those too. See our Asheville service page for wells, septic and water treatment in town.
Outside Asheville, the Buncombe County pump repair page covers Candler, Leicester, Weaverville, Fairview and Black Mountain. We also cover Waynesville and Canton, Hendersonville and Fletcher, Brevard, Sylva, Marshall and Mars Hill, and out to Bryson City, Burnsville, Marion and Tryon. How quickly we can get there depends on the day’s schedule and how far out you are, so call and we’ll give you an honest answer. If your question isn’t about one town, our frequently asked questions cover wells, septic and springs in general.
Each county page covers the towns, permits and well conditions in that area:
- Buncombe County
- Haywood County
- Hendersonville & Henderson County
- Madison County
- Transylvania County
- Jackson County
- Macon County
- Swain County
- McDowell County
- Tryon & Polk County
- Rutherfordton & Forest City
- Mitchell County
- Yancey County
Town pages: emergency well repair in Asheville, Candler, Weaverville and Canton; pressure tank replacement in Asheville; pump replacement in Leicester, Black Mountain, Fletcher and Hendersonville; and pump diagnostics in Sylva. For everything else we do on wells, see well services. Buying a house with a well? Start with a well inspection.
Well pump repair questions
Do you repair well pumps in Asheville?
Yes. We repair well pumps, pressure tanks, switches and controls for homes in and around Asheville that are on a private well, from our shop in Candler just west of town. Call (828) 222-4160 and tell us what the water is doing.
My Asheville house is on city water. Can you help?
If the whole house is on city water, an outage or pressure problem is the city’s to fix, not a well pump. If you also have a well for a garden, barn or backup, or a booster pump on the line, we can work on that. If an old well is still tied into the house plumbing, it needs to be separated or set up with a proper backflow arrangement.
My well quit after a thunderstorm. Is the pump fried?
Not always. Lightning and power surges often take out the pressure switch, the control box capacitor or a breaker before they hurt the pump down in the well. We test those parts first. If the surge did reach the motor, we’ll show you the readings before anything gets pulled.
Should I keep resetting a tripped breaker?
No. If the well breaker trips a second time, leave it off and call. Resetting it over and over can make a wiring or motor problem worse.
Is low water pressure always a bad pump?
No. A waterlogged pressure tank, a worn pressure switch, a clogged sediment filter or a leak in the line to the house cause low or surging pressure more often than a worn-out pump. We check those before we talk about the pump.
What should I tell you when I call?
The address, when the water stopped, whether any faucet still works, what the breaker and pressure gauge are doing, whether you hear the pump try to start, and how deep the well is if you know.
How much is well pump repair?
It depends on what failed. A pressure switch, control box part or wiring fault at the surface is a much smaller job than pulling a pump. If the pump has to come out, well depth, pump size, the condition of the wire and drop pipe, and how hard the wellhead is to reach all change the price. We test first and give you a price for the repair before any work starts.
When do you replace a pump instead of repairing it?
When testing shows the motor or pump end is done, or the same failure keeps coming back. We also check the tank and switch so a new pump isn’t fighting worn-out equipment.
Do you drill new wells?
No. We don’t drill, but we’ll refer you to a driller we trust and handle the pump, wiring and hookup. We also repair and service existing wells.
What can cause a well pump to stop working?
A pump can stop because of a tripped breaker, a failed pressure switch or control box, a seized or burned-out motor, a broken wire, a clogged intake, or a well that has run low. We test those possibilities before we pull a pump. If the house is dry, start with the no-water checks.
Well pump trouble in Asheville?
Send the address and what the well is doing. If you’re out of water, call instead and we’ll get you on the schedule.
