Shallow Well Pumps
Jet Pump Repair in Asheville & Western NC
A jet pump pulls water from a shallow well, spring or cistern. When it loses prime or stops, Case Water Systems diagnoses the pump, suction line, valves and tank.
Fully licensed and insured. Work is performed onsite by a licensed contractor.
Lost prime?
What a jet pump is, and the signs it’s in trouble

Most deeper mountain wells use a submersible pump that hangs inside the well. Older and shallower wells, and a lot of spring and cistern setups, still use a jet pump in a crawlspace, basement, pump house or well house. It sits above ground and uses suction, or a jet assembly, to pull water up to the house.
A jet pump depends on a full suction line, so its failures look different from a submersible’s. Watch for:
- You have to prime it again every few days or weeks
- The motor runs, but little or no water comes out
- Pressure drops off during a shower or when two faucets run
- Rapid on-off clicking, or a pump that runs and never shuts off
- Grinding, squealing or a hot motor
Don’t keep priming it over and over. A pump that runs dry can burn itself up, turning a small suction-side fix into a new pump.
How we track down the problem
Jet pump work starts on the suction side, not with replacing the pump. We check:
- Whether every fixture is dry or only some, and whether it started suddenly or over days
- Prime, the suction line and its fittings, and the foot valve or check valve
- How much water is left in the well, spring box or cistern feeding the pump
- The pressure switch, the pressure tank’s air charge and any visible leaks
- Incoming power, and how the pump starts, runs and shuts off
On jet systems, plenty of no-water calls come down to an air leak, a stuck foot valve or a waterlogged pressure tank rather than a dead pump. You hear what failed and what the repair costs before we start.
Repair, replace, or switch to a submersible?
On a shallow well with a sound suction line, a like-for-like jet pump is often the right fix. If the pump itself is done, we match the new one to the depth, the water level and the existing piping. When a jet pump keeps failing on a well deep enough for a submersible, or it struggles to push water up to a house on the hill, we lay out both options and what each one involves before you decide. See well pump replacement for how we size pumps, and Asheville well pump repair for submersible pumps and controls.
With an existing well, we take care of the hookup using whichever pump fits, jet or submersible. For a newly drilled well, we refer you to a driller we trust and handle the pump, pressure tank and water system afterward. Pumps fed by a spring box or storage tank are covered under spring water systems and cisterns and storage tanks.
Where we work on jet pumps
Older properties are where jet pumps show up most: farmhouses in Leicester, Sandy Mush and Candler near our shop, small well houses toward Weaverville and Barnardsville, and valley homes around Canton and Waynesville that still run the original jet pump in a crawlspace or pump house. We also serve Asheville, Black Mountain, Fairview, Hendersonville, Brevard, Mars Hill and the rest of our 13 counties.
- Asheville
- Candler
- Leicester
- Weaverville
- Black Mountain
- Fairview
- Canton
- Waynesville
- Hendersonville
- Mars Hill
- Brevard
- All towns and counties
For pump work by county, see Buncombe, Haywood, Henderson and Madison, or well diagnostics if you’re not sure what’s wrong.
Common jet pump questions
Do you repair jet pumps as well as submersible pumps?
Yes, both. Jet pumps sit above ground and show up on shallow wells, older systems and some spring or cistern setups.
Why does my jet pump keep losing prime?
Air is leaking into the suction side, usually through a bad suction line or fitting, a worn foot valve or check valve, or a water level that has fallen out of the pump’s reach. We find the leak or failed part before replacing any pump.
Is it OK to keep priming the pump myself?
Once to get water back is fine if you know how. If it keeps losing prime, stop and call. Running a jet pump dry over and over can ruin the seal or burn up the motor.
Can you replace a jet pump with a submersible pump?
Sometimes. It depends on the well depth, the water level, the casing size and how the system is piped. We look at those before recommending a like-for-like jet pump or a different setup.
My jet pump draws from a spring or cistern. Can you service it?
Yes. Above-ground pumps are common on spring and storage-tank systems, and we check the intake, foot valve and the water level in the box or tank along with the pump.
Need the jet pump looked at?
Send the address, what the pump is doing, and photos of the pump and tank if you can get them. We’ll call or text to confirm a time. If you have no water, call (828) 222-4160.