Skip to content

Water Treatment

Water Softener Repair in Asheville & Western NC

When hard water comes back, the brine tank is full of unused salt, or a unit runs all night, Case Water Systems troubleshoots and repairs whole-house softeners.

Fully licensed and insured. Work is performed onsite by a licensed contractor.

Water softener repair

Check these first

  • Is the bypass valve open? It’s easy to bump.
  • Push a broom handle into the salt. A hard crust with a gap under it is a salt bridge.
  • Did the power go out? Many valves lose their clock and settings.
  • Is the salt level going down at all over a few weeks?
  • Is there water on the floor around the valve or the drain line?

If all of that looks fine and the water is still hard, the valve or resin needs a closer look.

How a softener regenerates, and why salt does not always mean it is working

A softener takes hardness out of the water as it flows through resin, then periodically rinses that resin with brine and sends the waste to a drain. If the control valve never starts a regeneration, the bypass is open, or a salt bridge has formed in the brine tank, the unit can sit there full of salt and still send hard water to the house. We check those things before replacing parts.

Water softener with brine tank, resin tank and control valve plus sediment filter installed in a crawlspace in Western NC
Water softener, brine tank and sediment filter in a Western NC crawlspace.

Salt bridges, fouled resin and settings after a power outage

A salt bridge is a hard crust that forms over the water in the brine tank, so the unit thinks it has brine when it does not. Salt that has turned to mush can plug the well in the tank. Iron, manganese or sediment can foul the resin itself, especially on untreated well water; a softener is built for hardness, not for heavy iron or sulfur. See iron and sulfur treatment.

After a power outage, the clock and regeneration settings on many valves are lost, and the unit may stop cycling or run at the wrong time. We restore the settings from the water test and the household’s use, rather than guessing.

Leaks, drains and whether to repair or replace

We look for leaks at the valve, bypass, drain line and fittings, and for a drain that is backed up or frozen. Sometimes a control valve, injector or seal is all that is wrong. If the resin is spent or fouled, or the valve body is cracked, replacement can be the better answer. If you are starting from scratch, see water softener installation and water testing.

Well water treatment tank installed beside pressure tanks
Case Water Systems job photo: a treatment tank on a well system.

Common softener repair questions

Can you fix a softener someone else installed?

Yes. We troubleshoot and service existing whole-house softeners on wells and springs no matter who put them in, and tell you plainly whether repair or replacement makes more sense.

Why is my water hard again even though the softener has salt?

Common causes are a salt bridge in the brine tank, a control valve that is not starting regeneration, a bypass valve left open, or resin that has been fouled by iron. We check each of these before replacing anything.

Why does my softened water smell or look rusty?

A softener is built for hardness. Iron, manganese or sulfur coming through can foul the resin and show up as stains or odor. A water test tells us whether the softener needs service or whether another type of treatment belongs ahead of it.

The softener stopped cycling after a power outage. What happened?

Many control valves lose their clock and regeneration settings when the power goes out. The unit may sit idle or run at the wrong time until those settings are restored to match the hardness and the household’s use.

Should I repair this softener or replace it?

If the problem is a bridge, a setting, a seal or a valve part, repair is often enough. If the resin is spent or fouled, or the valve body is cracked, replacement is usually the better answer. We explain that after we look at the unit.

Tell us what your softener is doing

Send the address, whether the water feels hard again, and whether the brine tank still has salt in it.

Ask Case Water Systems

Choose what you need help with. This guided helper can point you to the right service.

For urgent no-water problems, call us.

Call (828) 222-4160